Mechanical Engineering tutorials videos
How to install an engine rocker cover.
Mechanical Engineering tutorials videos
Flywheel installation and working explained.
This video shows Flywheel installation and its working.
Most people will not have seen, where a flywheel is fixed on an engine. So this video gives you that opportunity. Engineering tutorials
Flywheel is the power take off point of an engine. It is mounted to the crank shaft and takes the power from the crank shaft to the transmission (gear box). In this video you can see the flywheel casing and the crank shaft mounting point of the flywheel. How fly wheel is manually aligned with the crank shaft is also shown here.
Mechanical
Engineering tutorials videosMost people will not have seen, where a flywheel is fixed on an engine. So this video gives you that opportunity. Engineering tutorials
Flywheel is the power take off point of an engine. It is mounted to the crank shaft and takes the power from the crank shaft to the transmission (gear box). In this video you can see the flywheel casing and the crank shaft mounting point of the flywheel. How fly wheel is manually aligned with the crank shaft is also shown here.
Working of engine oil cooler and its components.
These videos explain about the Engine oil cooler -- how it works, about
its ports in detail. The video starts by showing the location of engine
oil cooler on the engine block.Automobile
Engineering tutorials
View this full video to learn about the topics mentioned below: Hydraulic tutorials
Cooler mating point with engine Fuel filter aligning point, How Oil cooler cools the oil, to locate the Internal port of the oil cooler through which oil reached the chamber, location of engine oil filter, port through which the filtered oil passes, to locate the main oil gallery, to see the Engine coolant jacket, Oil filling point
View this full video to learn about the topics mentioned below: Hydraulic tutorials
Cooler mating point with engine Fuel filter aligning point, How Oil cooler cools the oil, to locate the Internal port of the oil cooler through which oil reached the chamber, location of engine oil filter, port through which the filtered oil passes, to locate the main oil gallery, to see the Engine coolant jacket, Oil filling point
How to manually set a crank shaft to engine.
Automobile Engineering tutorials This was documented while assembling as diesel engine, as you see this video you can see that, the cylinder block is inverted used an engine manipulator for the installation of the crank shaft. Crankshaft mating point or area is clearly visible. The crank shaft has been manually lifted and kept on the slot over the crank shaft bearings.
Detailed inspection and analysis of piston and connecting rod.
This video explains about the diesel engine piston and crank shaft.
Points to be noted:Mechanical Engineering tutorials videos
Piston skirt: It is the side wall of the piston as show in the video, this portion will be encaging with the cylinder walls.Engineering tutorials
1st compression ring: The purpose of this ring is to prevent compression leak. This ring is connected close to the piston top.
2nd compression ring: The purpose of this ring is also to prevent compression leak. This ring is fixed beneath the 1st compression ring.
Points to be noted:Mechanical Engineering tutorials videos
Piston skirt: It is the side wall of the piston as show in the video, this portion will be encaging with the cylinder walls.Engineering tutorials
1st compression ring: The purpose of this ring is to prevent compression leak. This ring is connected close to the piston top.
2nd compression ring: The purpose of this ring is also to prevent compression leak. This ring is fixed beneath the 1st compression ring.
Detailed inspection and analysis of an Engine cylinder block.
The cylinder block is actually a casting and to it the required ports are drilled. The cylinder block shown here is a Jcb engine block. This has ports in all the six sides as explained.Mechanical Engineering tutorials videos
Top side: We can see the 4 cylinders, the water jackets around it with internal galleries through the block which circulate water to cool the engine. Oil hole to the engine head for lubrication of the components over there. Engine oil drains ports and the thermostat coolant gallery. Head mounting bolt ports. Automobile Engineering tutorials
How hydraulic ram works.
The hydraulic ram is used in a hydraulic circuit for accomplishing a particular work. It actually converts the hydraulic pressure energy to mechanical energy "productive work". This video clearly explained how a hydraulic ram works and how the resultant components linked with it moves for carrying out a work. It also covers the function and working of the control valve or valve block and its spool movement resulting in the corresponding movement of the ram.
Mechanical Engineering tutorials videos
How ARV works.
ARV's are used in hydraulic circuits to protect the hydraulic components. This is also called as safety valve, used to vent the pressure during over loading and thereby safeguarding the system. This video clearly explains how it works in a construction equipment hydraulic circuit.
Mechanical Engineering tutorials videos
Drifting Vs Oversteer.
When you drive and reach the limits of grip on a corner, two scenarios called oversteer happens and controlled over steer is drifting. Both these scenarios are explained with animation in this topic.
Mechanical Engineering tutorials videos
Drifting explained.
Drifting is the process of controlling the over steer. While taking a turn when the tyre looses the traction or grip, it can result in oversteer. This over steer is controlled and made to advantage is called "Drifting".
Mechanical Engineering tutorials videos
Dismantling and explained a Starter motor
This video helps to identify the internal component of a starter motor.
In this video a starter motor is dismantle and assembled back.Mechanical
Engineering tutorials videos
A starter is a type of electrical machine which converts electrical energy into mechanical energy. Engineering tutorials
The electrical energy is obtained from the battery. When the starter switch is operated, current flows through the starter (the field coils and the armature conductors) and two magnetic fields are set up.
A starter is a type of electrical machine which converts electrical energy into mechanical energy. Engineering tutorials
The electrical energy is obtained from the battery. When the starter switch is operated, current flows through the starter (the field coils and the armature conductors) and two magnetic fields are set up.
Understeer explained.
This video explains about understeer "how it happens and how it can be avoided".Mechanical
Engineering tutorials videos
While taking a turn when the tyre looses the traction or grip, it can result in understeer or oversteer.
How understeer happens:
How understeer happens:
Automobile
Engineering tutorials When a vehicle is taking a turn, it normally moves towards the apex. The front
Oversteer explained - Animation.
Automobile Engineering tutorials
While taking a turn when the tyre looses the traction or grip, it can result in understeer or oversteer.
How oversteer happens:Engineering tutorials
When a vehicle is taking a turn it normally moves towards the apex. The rear tyre looses adhesion or traction and
How to use a hydrometer.
Mechanical Engineering tutorials videos
As you can see in the video, hydrometer consists of a glass tube which has a float inside. On the bottom of the hydrometer we have the suction tube, for sucking electrolyte. On the top we have a rubber bulb, which is squeezed to suck the electrolyte into the hydrometer tube.
As the electrolyte enters the tube, the float tends to move. So we can get the specific gravity at the scale of the float where the electrolyte rests. Hydraulic tutorials
How to install an Air filter.
Mechanical Engineering tutorials videos
Air filter is one critical part of an engine. This is the unit which cleans the air which is sucked from the atmosphere to be supplied to the Engine inlet manifold. If this air is not effectively cleaned (has dust). It will result in reduced efficiency and gradual failure of the engine. Engineering tutorials
Tech Trix Info- Please VOTE and SUPPORT our Project from KERALA.
Our project has been selected in Mahindra “Spark the rise-2” among the 120 projects selected from all over India. Only 2 projects have been
selected from Kerala.
This project is about - Free Engineering tutorial portal and Engineering
project assistance and technical assistance.
We need you support and vote to get to the next round, you
can see our project on: http://www.sparktherise.com/projectdetails.php?pId=7147
you can vote by giving a miss call from an Indian mobile number to +912261850957. A confirmation
SMS will be sent to you after your call, you will not be charged for this.
 |
| Voting Format: Only mobile no: accepted. |
This project is all about Engineering tutorials, to improve
the employability of students and we are also planning to providing technical
support to students and engineers. Anyone with internet facility can access
these tutorials and learn.
Currently we have a Youtube Engineering tutorial channel: www.youtube.com/techtrixinfo and
a blog www.techtrixinfo.com. This
contains video tutorials on engineering topics. Currently we are having 2000+
visitors/day and 1000+ subscribers in our youtube channel and 200+ visitors/day
in our blog. We also have a face book group: http://www.facebook.com/groups/techtrixinfo/
with 2060+ members and a face book page:
http://www.facebook.com/pages/TechTrixInfo/271447906234307
with 300+ Likes.
We are focusing in creating good and advanced Engineering
tutorial topics in all streams of engineering which could improve the
employability of students and engineers. Our unique advantage is that we are
capable of creating more tutorials on technology used in construction equipment
machines like Mahindra Earth Master, JCB etc which are not available in books
and internet, which will help young engineers to explore the new opening in this
field.
We are also providing support to Mr. Chanayil Clites Anil and Indian from Kerala who has developed and patented the “Six stroke engine” on 25 May 2012 patent no: 252642 as he is trying to further develop it. We have achieved 200+ engineering video tutorials and nearly 2.5 lakh viewers for our video tutorials in our Youtube Engineering tutorial channel: www.youtube.com/techtrixinfo and 45000+ views/ 250+ tutorial articles in our blog www.techtrixinfo.com. We have also developed an android application to get access to this tutorial and will be available by first week of November on Google play store.
We are also providing support to Mr. Chanayil Clites Anil and Indian from Kerala who has developed and patented the “Six stroke engine” on 25 May 2012 patent no: 252642 as he is trying to further develop it. We have achieved 200+ engineering video tutorials and nearly 2.5 lakh viewers for our video tutorials in our Youtube Engineering tutorial channel: www.youtube.com/techtrixinfo and 45000+ views/ 250+ tutorial articles in our blog www.techtrixinfo.com. We have also developed an android application to get access to this tutorial and will be available by first week of November on Google play store.
How to check hydraulic pressure of JCB.
Hydraulic pressure is the most critical parameter which determines the efficiency of hydraulic machinery. The MRV -- main relief valve controllers the hydraulic pressure. The main relief valve is set to protect the hydraulic pump from back pressure. It is set at a particular pressure which the hydraulic pump can hold. If more back pressure comes in, it opens up to release it.Engineering tutorials
How to drive and operate a crane.
Cranes are widely been used these days for construction works, wood handling etc. This product is a result of Construction equipment revolution worldwide. Engineering tutorials In earlier days in India, Elephants were used for such applications, now it has been replaced with cranes. This is a hydraulic machine which works on the basic principle of Pascals law. The technology is a combination of
Beauty of tubeless tyres.
Process of fixing the puncher of a tube less tyre.Mechanical Engineering tutorials videos
One our way back from the work site, our vehicle Mahindra Xylo rear LH tyre got puncher. As we inspected the tyre and found that it was a tube less one, this news was a relief, due to the fact that we had some time to drive and search for a mechanic.Automobile Engineering tutorials
That is the beauty of tubeless tyres because, unlike the tube tyres the air will not drain off quickly in this one. The process of
ABS Explained.
This system is a precision braking system used in modern automobiles.
Automobile Engineering tutorials
Components of an ABS:
1. Wheel speed sensor.
2. ABS control module.
3. Hydraulic motor.
4. Pressure release valves.
5. Brake pipe leading to caliper.
Working of ABS:
Engineering tutorials
All the wheels are fixed with brake calipers and wheel speed sensors. As the brake is
With and with out ABS Explained.
Mechanical Engineering tutorials videos
ABS -Anti lock breaking system is an advanced braking system used in modern vehicles which is hydraulically operated.
Without ABS: It's true that the vehicle can slow down quicker with ordinary braking system compared to the ABS. Automobile Engineering tutorials But it compromises on the vehicle stability while doing so. The vehicle can skid in this system and cause accidents. Hydraulic tutorialsEven steering lock can happen, which will restrict the driver from steering off the vehicle to avoid a collision.
JCB Attachments - Part 2
Attachments and application listed below:
1. Auger: Construction, laying electric pole, Agriculture plantation, industry fencing, real estate defense.Mechanical Engineering tutorials videos
2. JCB hammer master 360: quarry secondary breaking, pipe and cable laying trenching, foundation work and demolition, smelter, steel waste breaking used in back hoe loaders (BHL) like 3dx, 3dx super, 4dx, 3 dx xtra.
JCB attachments - Part 1
Engineering tutorials
Attachments and application listed below:
1.Disc cutter: Concrete cutting, Metal cutting, Stone cutting and used in BHL (back hoe loader machines)
2. Long reach attachment: Canal-de-silting, construction, material handling for high reach requirements in confined area used in tracked and wheeled excavators.
Mechanical Engineering tutorials videos
Subscribe to:
Posts (Atom)